How to Make a homemade penis pump?
Creating your own DIY penis pump is a straightforward process that can be accomplished using common household items. If you already have a 16.9-ounce soda bottle, a large water bottle, plastic tubing, and either a brake bleeding kit or an aquarium syphon, then you have most of the necessary items. If you are interested in creating a homemade penis pump, you can find three simple, step-by-step tutorials below.
DIY Penis Pump 1
To assemble the penis pump, you will require the following materials:
List of Supplies
Clear water bottle with lid
Hand held vacuum pump
Plastic tubing
Silicone sealant
Drill
Thick sponge
Strong duct tape
Tips: When searching for a suitable vessel to create a penis pump, consider using a plastic container, cylinder, or bottle that closely matches the size of your penis. Water bottles and plastic storage containers are considered to be food-grade, meaning they are safe for use with food and beverages and are therefore also safe for use with the human body. Additionally, for individuals with a modest size, the plastic cylinder included in a brake bleeding kit can be suitable for creating a DIY penis pump.
When selecting a pump, there are several types available for different purposes, such as hardware pumps, automotive pumps, blood pressure bulbs, and breast pumps. For this project, any device that can extract air and is compatible with plastic tubing, either by being attachable or by including it, will be suitable.
Instructions
Step 1: Let's start by drilling a hole in the bottom of the water bottle. Make sure the hole is the same size as the plastic tubing. Tip: To find the perfect drill bit size, simply try inserting each bit into the end of the tubing. Once you find the bit that fits just right, try going to the next size up.
Step 2: Grab your thick sponge. Sure, go ahead and flip the water bottle over. Then, you can trace the opening onto the sponge. Why don't you set the sponge aside for now? You can work on it later once the sealant has dried.
Step 3: Take the end of the plastic tubing and give it a nice coating of clear sealant, about 1/4 inch on the outside.
Step 4: Then, gently place the end of the tubing into the hole that you carefully drilled in the bottom of the water bottle. It should fit perfectly. Sure, go ahead and apply some sealant to the area where the tubing goes in to create a nice, tight seal.
Step 5: Lay the water bottle gently on its side and carefully prop the plastic tubing up so that it fits snugly into the hole in a straight manner. Make sure to let it dry based on the instructions provided with the sealant you've chosen.
Step 6: Let's go back to the sponge you traced earlier! To make it easier, you can use scissors to carefully cut out the center just outside the circle you drew earlier.
Step 7: Grab some scissors and carefully cut out the center of the sponge, giving it a fun donut shape! Make sure to leave a thick ring, as it will provide extra cushioning for the opening of the penis pump.
Step 8: Gently slide the circular piece of sponge over the mouth of the water bottle. Sure, if it's too tight, you can simply cut a spot in the circle to create a strip of sponge.
Step 9: Gently place the piece of sponge around the mouth of the water bottle, making sure to leave enough sponge to fold over on each side. Next, let's cut a strip of strong duct tape.
Step 10: Bring the ends of the sponge together and gently secure the sponge ring with a small piece of tape. Please remember to fold the sponge over the rim of the water bottle while applying the tape. Please make sure to gently smooth out the tape on both the inside and outside of the bottle.
Step 11: Keep applying strips of tape around the bottle, making sure they overlap and are firmly sealed against each other, both on the inside and outside of the water bottle.
Step 12: Now, simply slide the other end of the tubing onto the automotive hand pump. Great! Your DIY penis pump is all set to go. Here's a helpful tip: If you're having trouble creating suction, make sure to check that the hole you drilled is properly sealed. Also, remember to press the opening of the pump firmly against your body to create a good seal. This should help you get the suction you need.
DIY Penis Pump 2
This homemade penis pump is both easier to make and extremely affordable. Here is a list of the items you will need:
List of Supplies
Soda bottle
Siphon and tubing for fish tanks
Silicone sealant
Thick sponge
Strong duct tape
Drill
Sharp, serrated knife or hand saw
Tips: You can use a bottle that closely matches the size of your erect penis. Make sure to select a bottle with thick walls to prevent easy collapse.
Instructions
Step 1: Utilize the serrated knife to carefully remove the bottom portion of the soda bottle, ensuring that it is completely empty. Tip: Ensure that the bottom is cut as evenly as possible, as this will be the end that seals against your body.
Step 2: Begin by removing the cap from the soda bottle. Then, use a drill to carefully create a hole in the cap. Tip: To determine the correct drill bit size, insert different drill bits into your tubing until you find one that fits securely. Next, use the drill bit that is one size larger.
Step 3: Apply the sealant to the exterior of the tubing.
Step 4: Insert the tubing into the hole in the soda cap, ensuring it goes in approximately 1/2 an inch. Next, carefully apply the sealant to both the outer and inner surfaces of the tubing and the bottle cap. Follow the instructions on the sealant to properly set aside and allow it to dry.
Step 5: While allowing the cap to dry, carefully position the soda bottle on top of a substantial and absorbent sponge. Use a marker to trace around the opening.
Step 6: Utilize a pair of scissors to carefully cut out the circle from the sponge, ensuring that you cut just outside the line that you previously drew.
Step 7: With the scissors, carefully cut out the center of the sponge in the shape of a donut. Continue trimming until you are able to effortlessly slide the sponge ring along the bottom of the bottle without any bending of the sides.
Step 8: Carefully place the sponge ring around the opening at the bottom of the bottle, ensuring that there is sufficient sponge material to fold over and completely cover the rim. Next, cut a strip of durable duct tape that will effectively create a seal to prevent any leaks.
Step 9: Start folding the sponge and secure it in place by using tape. Ensure that each piece overlaps with the next one and firmly press down the tape.
Step 10: Proceed with wrapping the tape around the cut end of the bottle, ensuring that it forms a secure and even seal throughout.
Step 11: After allowing the sealant on the cap and tubing to dry, securely screw the cap back on. Your homemade penis pump is now ready for use. Tip: If you are unable to create suction, make sure to check that the tubing is properly sealed and airtight. You have the option to apply additional sealant or completely seal the cap.
Simple DIY Water Penis Pump Without the Need for Special Tools
To create a homemade penis pump, you will only require two items. This DIY pump is ideal for men who are more modestly endowed. Warning: This pump generates a highly potent suction force and must be handled with extreme caution!
List of Supplies
Accordion style sink plunger
Large sponge
Instructions
To begin, lay the accordion-style washbasin plunger on its side. Take a large car wash sponge and roll it into a circular shape. Then, insert the rolled sponge into the plunger, making sure to press it as deeply as you can into the bellows.
